Audi A6 Typ 4G (2011–2018) Workshop Manual / Electrical System / Electrical Equipment / Wiring / Relay and Fuse Carrier Behind Instrument Panel on Driver Side, Removing and Installing
Relay Carrier under Left Instrument Panel, Removing and Installing
Special tools and workshop equipment required
- Fiber-Optic Repair Set - Connector Protective Caps -VAS6223/9- from Fiber-Optic Repair Set -VAS6223B-
Removing
-Remove the driver side footwell vent. Refer to→Heating, Ventilation and Air Conditioning;Rep. Gr.87;Air Guide; Driver Side Footwell Vent, Removing and Installing.
-Disconnect the wires -1 and 2- from the relay carrier.
-Release the retaining spring -4- and remove the relay carrier -6- downward.
-Disconnect the connector -5-, if applicable.
-Disconnect the fiber optic cable connector-3- and free it up.
-Seal open wiring harness connector -2- with Fiber-Optic Repair Set - Connector Protective Caps - VAS6223/9--item 1-.
Note
The protective cap prevents contamination of or mechanical damage to end face of fiber optic cable which would impair signal transmission.
-Release the tab in direction of -arrow- and remove fuse panel D -item 2- from the relay carrier -1- toward the rear.
-Open the clip and remove the auxiliary fuse panel-2-.
-Release the clips -arrows- and remove the relay -1- and the control modules from the relay carriers.
-Release the retainers -arrows- and remove the relay carrier -2- from the relay/fuse panel -item 1- to the rear.
Note
Check the exact connector assignment in the current wiring diagram →Wiring diagrams, Troubleshooting & Component locations.
Installing
Install in reverse order of removal.
Fuse Panel D -SD-, Removing and Installing
Removing
-With the ignition switched off, disconnect the ground cable from the battery. Refer to →Chapter "Battery, Disconnecting and Connecting".
-Remove the driver side instrument panel cover. Refer to→Body Interior;Rep. Gr.68;Storage Compartments and Covers; Driver Side Instrument Panel Cover, Removing and Installing.
-Release the tab -arrow- and remove fuse panel D -item 2- from the relay carrier -1- toward the rear.
-Unlock the release and remove it from the fuse carrier.
-Remove the fuses from the fuse carrier.
-Open the clips in direction of -arrows- and remove the fuse carrier cover.
-Pull off retaining strip -1- for the connectors in direction of -arrow- and remove the connectors from the plug-in socket
Note
Check the exact connector assignment in the current wiring diagram →Wiring diagrams, Troubleshooting & Component locations.
Installing
Install in reverse order of removal. Note the following:
-Connect the battery. Required steps: vehicles without high voltage system. Refer to vehicles with high voltage system.
Relay Panel Mount, Removing and Installing, Under Instrument Panel and Left Side, Vehicle Electrical System Control Module -J519-
Removing
-Remove the vehicle electrical system control module. Refer to →Chapter "Vehicle Electrical System Control Module -J519-, Removing and Installing".
-Remove the headlamp range control module. Refer to→Chapter "Headlamp Range Control Module, Removing and Installing".
-Remove the left instrument panel vent. Refer to→Body Interior;Rep. Gr.70;Instrument Panel; Instrument Panel Vent, Removing and Installing.
-Slide the extension -2- from the socket set between the air duct -3- and the instrument panel.
-Remove the nuts -4 and 5-.
-Remove the mount -6- from the threaded pins.
-Disengage the retaining pins -1- on the mount at the side guide in the A-pillar in direction of-arrow- while pulling the mount toward the passenger compartment.
-Release the tabs -3- in direction of -arrow A- and disengage the mount for the headlamp range control module-1- from the mount-2- in direction of-arrow B-.
Installing
Install in reverse order of removal. Note the following:
-Engage the retaining pins -1- on the mount -3- at the side guide in the A-pillar -arrow-.
-Tighten the nuts -2-.
READ NEXT:
Relay and Fuse Panels In Luggage Compartment on Right Side, Removing and Installing
Fuse Panel F -SF- in Right Luggage Compartment, Removing and InstallingRemoving-With the ignition switched off, disconnect the ground cable from the battery. Refer to →Chapter "Batte
Control Modules
Overview - Control Modules1-Garage Door Opener Control Module -J530-Removing and installing. Refer to →Chapter "Garage Door Opener Control Module, Removing and Installing".
Connectors
Overview - Connector1-Left Front Door Cut-Off ConnectorDisconnecting. Refer to →Chapter "Front Door Cut-Off Connector, Disconnecting".2-Right Front Door Cut
SEE MORE:
Rear Brake Caliper, Removing and Installing
Brake Caliper, Removing and Installing, Steel BrakesSpecial tools and workshop equipment requiredTorque Wrench 1332 40-200Nm -VAG1332- CautionThis procedure contains mandatory replaceable parts. Refer to component overview and parts catalog prior to starting procedure.Mandatory Re
Fuel filler door emergency release
If the central locking system is faulty, the fuelfiller door can be unlocked manually.Fig. 176 Right side trim in the luggage compartment : removingthe trimFig. 177 Luggage compartment: fuel filler door emergencyreleaseRemoving the side trimTo remove the right side trim, first remove the